ASME B18.2.1a-1999 square and hex bolts and screws (inch series)
|
ID：
|
28169E4FE9F84C2182E73BF09FAF7E63
|
|
文件大小(MB)：
|
0.53
|
|
页数：
|
16
|
|
文件格式：
|
pdf
|
|
日期：
|
2010-8-22
|
|
购买：
|
购买或下载
|
文本摘录（文本识别可能有误，但文件阅览显示及打印正常，pdf文件可进行文字搜索定位）：
AN AMERICAN NATIONAL STANDARD,ASME B18.2.1a-1999,ADDENDA,to,ASME B18.2.1-1996,SQUARE AND HEX BOLTS,AND SCREWS (INCH SERIES),THE AMERICAN SOCIETY OF MECHANICAL ENGINEERS,Three Park Avenue ?New York, NY 10016,Date of Issuance： October 8, 1999,ASME is the registered trademark of The American Society ol Mechanical Engineers,This code or standard was developed under procedures accredited as meeting the criteria for,American National Standards. The Standards Committee that approved the code or standard,was balanced to assure that individuals from competent and concerned interests have had an,opportunity to parlicipate. Tho proposed code or standard was made available for public review,and comment that provides an opportunity for additional public input from industry, academia,regulatory agencies, and the public-at-large.,ASME does not ""approve," -rate/ or -endorse" any item, construction, proprietary device,or activity.,ASME does not take any posi( or persontsl affiliated with industry is not to,be interpreted as government or industry endorsement of this code or standard.,ASME accepts responsibility for only those interpretations issued in accordance with governing,ASME procedures and policies which precludes the issuance of interpretations by individual,vo*unieers.,No part of this document may be reproduced in any form,m an electronic retrieval system or otherwise.,without the prior written permission of the publisher,The American Society of Mechanical Engineers,Three Park Avenue, New York, NY 10016,Copyright . 1999 by,THE AMERICAN SOCIETY OF MECHANICAL ENGINEERS,All Rights Reserved,Printed in U.S A.,ASME B18.2.1a-1999,Following approval by (he ASME BIS Committee and ASME, and after public review. ASME BI8.2.la-,1999 was approved by (he American National Standards Institute on April 9. 1999.,Addenda to (he 1996 edition of ASME BI8.2.1 arc issued in the form of replacement pages. Revisions,additions, and deletions are incorporated directly into the affected pages, h is advisable, however, that this,page, the Addenda title and copyright pages, and all replaced pages be retained for reference.,SUMMARY OF CHANGES,This is the first Addenda to be published to ASME Bl8.2 1-1996.,Replace or insert the pages listed. Changes given below are identified on the pages by a margin note, (a),placed next to the affected area The pages not listed are the reverse sides of (he listed pages and contain,no changes.,Page Lt)caiion Change,vi.l Correspondence With B18,Committee,Added,ix Contents Updated to reflect Addenda,10 Table 3 In fifth column, second entry corrected by,errau to read 1 l/tt),16-18 Table 4. Note (5) Four equations deleted by errata,Fig. 2 Four equations added by errata,Table 4. No(c (11) Revised,23, 24 Fig. 5 Four equations added by errata,Table 6. Note (7) Four equations deleted by errata,Table 6. Note (11) Revised,33 Appendix I Deleted,35 Appendix II Revised in its entirety,bylHf，SCa MswlW AS??E,No rspnxiix*x' c* cuMOrturg p?m?n?d 如刘 IMS,CORRESPONDENCE WITH B18 COMMITTEE (a,General. ASME Standards arc developed and maintained with the inlenl to represent the,consensus of concerned interests. As such, users of this Standard may interact with the,Commitiee by requesting inierpretaiions, proposing revisions, and allending Committee,meetings. Correspondence should be addressed to;,Secretary, BI8 Main Committee,The American Society of Mechanical Engineers,Three Park Avenue,New York. NY IOOIfr-5990,Proposing Revisions. Revisions are made periodicaJly Io the Standard to incorporaie,change* that appear necessary or desirable, as demonstrated bv the experience gained from,the application of the Standard. Approved revisions will be published periodically.,The Committee welcomes proposals for revisions to this Standard. Such proposals should,be as specific as possible, ciling the paragraph nuinberfs), the proposed wording, and a,deuiled description of ihe reasons for the proposal, including any peninem documentation,interpretations. Upon request, the. Big Committee will render an interpretation of any,requirement of the Standard, [nterpretaiions can only be rendered in respon……
……